Εγχειρίδιο χρήσης Vertex² · Σελίδες PDF 45–54

Λίστα εντολών RS232 και IP/Telnet

ΛΙΣΤΑ ΕΝΤΟΛΩΝ RS232 ΚΑΙ IP/TELNET ΤΟΥ VERTEX²

Η υποδοχή RS232 του Vertex² αναμένει τα ακόλουθα σήματα βύσματος: TIP = TX [στέλνει δεδομένα από το Vertex²] RING = RX [λαμβάνει δεδομένα προς το Vertex²] SLEEVE = GND Παράμετροι: 19200, n, 1, χωρίς handshake

Αν χρησιμοποιείτε RS232, κάθε εντολή πρέπει να ξεκινά με την κεφαλίδα #Vertex² και να τελειώνει με carriage return \r ή newline \n. Αν χρησιμοποιείτε IP/TELNET, κάθε εντολή πρέπει να τελειώνει με carriage return \r ή newline \n, αλλά δεν χρειάζεται η κεφαλίδα #Vertex². Κάθε απόκριση θα έχει προστεθεί και carriage return \r και newline \n στη μορφή <cr><lf>

Η προεπιλεγμένη θύρα IP του Vertex² είναι 2210. π.χ. 192.168.1.100:2210 Χρησιμοποιείτε μόνο πεζούς χαρακτήρες

Μια γενική εντολή RS232 για εγγραφή τιμής

#Vertex2 set x y
where #Vertex2 is the header and all commands start with this header
set - indicates value will be written to Vertex²
x - target to be written
y - value or values

Μια γενική εντολή RS232 για ανάγνωση τιμής

#Vertex2 get x
where #Vertex2 is the header and all commands start with this header
get - indicates value will be read from Vertex²
x - target to be read

Μια γενική εντολή IP είναι όπως παραπάνω χωρίς την κεφαλίδα #Vertex². Πλήρης λίστα εντολών VERTEX²

#vertex2 set insel tx0 tx1
where tx0 and tx1 is [0-3] input port, or [4] for follow
Ex. #vertex2 set insel 2 3
Set tx0 to input 2 and tx1 to input 3

#vertex2 set inseltx0 x
where x is [0-3] input port, or [4] for follow
Ex. #vertex2 set inseltx0 1
Set tx0 to input 1 and keep tx1 as is

#vertex2 set inseltx1 x
where x is [0-3] input port, or [4] for follow
Ex. #vertex2 set inseltx1 1
Set tx0 to input 1 and keep tx0 as is

#vertex2 set ipaddr xxx.xxx.xxx.xxx
Sets the static IP address. Active when dhcp is turned off.
Ex. #vertex2 set ipaddr 192.168.1.222

#vertex2 set ipmask xxx.xxx.xxx.xxx
Sets the static IP network mask. Active when dhcp is turned off.
Ex. #vertex2 set ipmask 255.255.255.0

#vertex2 set ipgw xxx.xxx.xxx.xxx
Sets the static IP gateway address. Active when dhcp is turned off.
Ex. #vertex2 set ipgw 192.168.1.1

#vertex2 set dhcp x
Set the dynamic or static IP address selection. Dynamic = dhcp on
where x is [on / off]
Ex. #vertex2 set dhcp off

#vertex2 set tcpport x
Set the TCP port to be listened to for commands. Default is 2200
Requires a reboot to be applied.
Ex. #vertex2 set port 2201

#vertex2 set autosw x
where x is [on / off]
Enables or disables the autoswitch feature
Ex. #vertex2 set autosw off

#vertex2 set autoswprio x
where x is [on / off]
Enables or disables the autoswitch priority feature
Ex. #vertex2 set autoswprio off

#vertex2 set edidmode x
where x is [automix / custom / fixed / copytx0 / copytx1]
Ex. #vertex2 set edidmode automix

#vertex2 set edid audio x
where x is [stereo / 51 / full / native / tx1]
Sets the automix EDID audio flag
Ex. #vertex2 set edid audio native

#vertex2 set edid bt2020 x
where x is [on / off]
Sets the automix EDID bt2020 capability addition
Will not remove if existing on the sink - only adds if missing
Ex. #vertex2 set edid bt2020 on

#vertex2 set edid yuvremove x
where x is [on / off]
Sets the automix EDID YUV/YCbCr capability force
Controls if the source sees a YCbCr capable sink
Ex. #vertex2 set edid yuvremove on

#vertex2 set edid hdr10 x
where x is [on / off]
Sets the automix EDID hdr10 capability
Will not remove if existing on the sink - only adds if missing
Ex. #vertex2 set edid hdr10 on

#vertex2 set edid hlg x
where x is [on / off]
Sets the automix EDID hlg capability
Will not remove if existing on the sink - only adds if missing
Ex. #vertex2 set edid hlg on

#vertex2 set edid dv x
where x is [on / off]
Sets the automix EDID Dolby Vision capability
Will not remove if existing on the sink - only adds if missing
Ex. #vertex2 set edid dv on

#vertex2 set edid dvremove x
where x is [on / off]
Sets the automix EDID to remove DV capability
Ex. #vertex2 set edid dvremove on

#vertex2 set edid dvlimit x
where x is [on / off]
Sets the automix EDID Dolby Vision frequency capability to 300Mhz max
Ex. #vertex2 set edid dvlimit on

#vertex2 set edid 3dremove x
where x is [on / off]
Sets the automix EDID to remove 3D capability
Controls if the source sees a 3D capable sink
Ex. #vertex2 set edid 3dremove on

#vertex2 set hdcp x
where x is [14 / auto]
Sets the hdcp level
in auto mode, depending on sink capability uses hdcp 1.4 or 2.2
Ex. #vertex2 set hdcp auto

#vertex2 set scale x
where x is [auto / custom / none]
Sets the scaling style for tx0 (tx1 is always automatic)
In auto mode, optimizes according to the best sink capabilities
Ex. #vertex2 set scale auto

#vertex2 set autonoupscale x
where x is [on / off]
Sets the mode for upscaling in tx0 output. Applies in "scale auto" mode only.
In "scale auto" mode enables/disables upscaling of 1080p content automatically to 4k.
Ex. #vertex2 set autonoupscale off

#vertex2 set edidtableinp0 x

#vertex2 set edidtableinp1 x

#vertex2 set edidtableinp2 x

#vertex2 set edidtableinp3 x
where x is [1 - 100] for edidtableinp0 and [0 - 100] for others
Sets the custom EDID for corresponding input port
For ports 1-3 table number 0 indicates copy port 0 table
Ex. #vertex2 set edidtableinp0 11

#vertex2 set edidalgo x
where x is [0 - 4]
Sets the automix algorithm
0 = Min video, min audio
1 = Min video, max audio
2 = Tx0 priority
3 = Tx1 priority
4 = Max video, max audio [default]

Ex. #vertex2 set edidalgo 4

#vertex2 set hdrcustom x
where x is [on / off]
Starts to output custom HDR metadata and ignores any input received HDR metadata.
Overrides all other hdrcustom options
Ex. #vertex2 set hdrcustom on

#vertex2 set hdrcustomhdr10only x
where x is [on / off]
Starts to output custom HDR metadata if and only if the input is HDR10.
This setting is used to replace the incoming HDR10 metadata.
Ex. #vertex2 set hdrcustomhdr10only on

#vertex2 set hdrcustomhlgonly x
where x is [on / off]
Starts to output custom HDR metadata if and only if the input is HLG.
This setting is used to replace the incoming HLG metadata.
Ex. #vertex2 set hdrcustomhlgonly on

#vertex2 set hdrcustomhlgonlyauto x
where x is [on / off]
Starts to output custom HDR metadata if and only if the input is HLG
and the sink has no HLG support.
This setting is used to replace the incoming HLG metadata.
Useful when turning on/off HLG capable sink while non-HLG sink is also connected.
Ex. #vertex2 set hdrcustomhlgonlyauto on

#vertex2 set hdrdisable x
where x is [on / off]
Stops sending any HDR metadata content
Ex. #vertex2 set hdrdisable on

#vertex2 set hdrdisablehdr10only x
where x is [on / off]
Stops sending any HDR metadata content if the input is HDR10
Ex. #vertex2 set hdrdisablehdr10only on

#vertex2 set hdrdisablehlgonly x
where x is [on / off]
Stops sending any HDR metadata content if the input is HLG
Ex. #vertex2 set hdrdisablehlgonly on

#vertex2 set avicustom x
where x is [on / off]
Starts to output custom AVI infoframe and ignores any input received AVI metadata.
Ex. #vertex2 set avicustom on

#vertex2 set avidisable x
where x is [on / off]
Stops sending any AVI infoframe content
Ex. #vertex2 set avidisable on

#vertex2 set cec x
where x is [on / off]
Sets the CEC engine
Ex. #vertex2 set cec on

#vertex2 set cecla x
where x is [video / audio]
Sets the CEC engine logical address. For video [14] and for audio [5].
Ex. #vertex2 set cecla audio

#vertex2 set archbr x
where x is [on / off]
Sets the ARC capability to include DD+ / ATMOS over DD+ capability.
Ex. #vertex2 set archbr on

#vertex2 set oled x
where x is [on / off]
Sets the OLED display visibility
Ex. #vertex2 set oled on

#vertex2 set oledrev x
where x is [on / off]
Sets the OLED display reversed colors
Ex. #vertex2 set oledrev on

#vertex2 set oledrot x
where x is [on / off]
Sets the OLED display rotation
Ex. #vertex2 set oledrot on

#vertex2 set oledpage x
where x is [0-4]
Sets the OLED display page
Ex. #vertex2 set oledpage 0

#vertex2 set oledfade x
where x is [0-255]
Sets the OLED display fade timer in seconds. After this time OLED goes blank
0 = no fade
Ex. #vertex2 set oledfade 60

#vertex2 set osd x
where x is [on / off]
Enables / disables osd
Ex. #vertex2 set osd on

#vertex2 set osdloc x y
where x is [1 - 1920] and y is [1 - 1080]
Sets the OSD information location coordinates. For 4k the values are 4x
Ex. #vertex2 set osdloc 50 850

#vertex2 set osdfg x
where x is [1 - 31]
Sets the OSD foreground color
Ex. #vertex2 set osdfg 20

#vertex2 set osdbg x
where x is [1 - 31]
Sets the OSD background color
Ex. #vertex2 set osdbg 20

#vertex2 set osdlevel x
where x is [0 - 7]
Sets the OSD opacity level
Ex. #vertex2 set osdlevel 4

#vertex2 set osdfade x
where x is [0-255]
Sets the OSD fade timer in seconds. After this time OSD info disappears
0 = no fade
Ex. #vertex2 set osdfade 20

#vertex2 set osdfield x y
where x is [source / video / videoif / hdr / hdrif / audio / rxhdrforce
rxvideoforce / ignoremetadata] and y is [on / off]
Sets the OSD field parameter visibility
Ex. #vertex2 set osdfield videoif off

#vertex2 set osdmaskloc x y x1 y1
where x and x1 are [1 - 1920] and y and y1 are [1 - 1080]
Sets the OSD mask information location coordinates. For 4k the values are 4x
Ex. #vertex2 set osdmaskloc 50 850 1900 900

#vertex2 set osdmask x
where x is [on / off]
Enables / disables osdmask
Ex. #vertex2 set osdmask on

#vertex2 set osdmasklevel x
where x is [0 - 7]
Sets the OSD opacity level
Ex. #vertex2 set osdmasklevel 4

#vertex2 set osdmaskgray x
where x is [0 - 15]
Sets the OSD gray level
Ex. #vertex2 set osdmaskgray 4

#vertex2 set osdtextloc x y
where x is [1 - 1920] and y is [1 - 1080]
Sets the OSD text location coordinates. For 4k the values are 4x
Ex. #vertex2 set osdtextloc 50 20

#vertex2 set osdtextneverfade x
where x is [on / off]
Osd text typically fades together with normal OSD.
This setting can disable fading.
Ex. #vertex2 set osdtextneverfade on

#vertex2 set osdtextstr x
where x max 64 characters
Defines the specific text string to be displayed. Must be in enlosed in quotation
Ex. #vertex2 set osdtextstr "HDFury 2019"

#vertex2 set osdtext x
where x is [on / off]
Enables / disables osdtext
Ex. #vertex2 set osdtext on

#vertex2 set mutetx0audio x
where x is [on / off]
Mute the tx0 hdmi audio output

Ex. #vertex2 set mutetx0audio on

#vertex2 set mutetx1audio x
where x is [on / off]
Mute the tx1 hdmi audio output
Ex. #vertex2 set mutetx1audio on

#vertex2 set analogvolume x
where x is [-30 to +10]
Sets the analog L/R audio jack output volume in dB.
Ex. #vertex2 set analogvolume -10

#vertex2 set analogbass x
where x is [-10 to +10]
Sets the analog L/R audio jack output bass level in dB.
Ex. #vertex2 set analogbass 5

#vertex2 set analogtreble x
where x is [-10 to +10]
Sets the analog L/R audio jack output treble level in dB.
Ex. #vertex2 set analogtreble -2

#vertex2 set reboot
Reboots the unit, does not clear any settings

#vertex2 set factoryreset x
where x is [1, 2, 3]
1 = Erase all settings but retain the custom EDID tables
2 = Erase custom EDID tables but retain other settings
3 = ERASE all settings and EDID tables
Ex. #vertex2 set factoryreset 3

#vertex2 set jvcmacro x
where x is [on / off]
Enables / disables JVC macro sending
Ex. #vertex2 set jvcmacro on

#vertex2 set jvcmacrosync x
where x is [on / off]
Enables / disables JVC macro sending on every sync instead of just at start once
Ex. #vertex2 set jvcmacrosync on

#vertex2 set jvcmacrodelay x
where x is [0 - 255]

Ορίζει την καθυστέρηση μεταξύ μιας αλλαγής λειτουργίας και της αποστολής της εντολής macro μέσω RS232

Ex. #vertex2 set jvcmacrodelay 25

#vertex2 set jvcmacrohdr10mode x
where x is [0 - 4]
0 = auto
1 = ignore metadata
2 = semiautomatic
3 = custom
Sets the current JVC macro mode
Ex. #vertex2 set jvcmacrohdr10mode 0